The article in the next paragraphs pertaining to How to Install a Bathtub is immensely engaging. Don't bypass it.
Mounting a bathtub isn't precisely brain surgery, but it does need solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is conveniently accessible, the task can move immediately; if you need to open a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will require a helper to vacate the old tub and also embeded in the brand-new one. See to it you have qualified on your own for the work and are comfortable trying it. As opposed to hiring a professional to take control of a halfway-completed job, it is far better to consider employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This short article will certainly assist you mount a brand-new bathtub in your bathroom if you have already bought a brand-new bathtub and also do not require to transform the setup of your previous water system pipelines.
Your devices and material checklist ought to make up the following:
Preparing for the Installation
First of all, the supporting framework supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you use every one of the supplied washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last setting.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be rather problematic as a result of the restricted accessibility that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipelines. When the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. When the faucets have been removed, the holes in the bath/basin will have to be cleaned of any kind of old sealing substance.
Before carrying on to fit the new faucets, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, position the tub in the called for position. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 tiny points.
The next goal is to make sure that the tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bath tub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the water system and also check all joints and new pipework for leaks and tighten them if required. Fill up the bath tub as well as also check the overflow outlet as well as the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as described in the producer's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been used at least once as this will settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in place between the faucet and also the sink. Safeguard the faucet in position with the producer offered backnut. Once the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet adapters. The former type ought to be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, creating the water to pass through the wall between the bathroom as well as the tiling, resulting in complications with moisture and possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can split fairly very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very occupied with How to Install a Bathtub and I really hope you enjoyed the blog post. For those who enjoyed our article kindly make sure you remember to share it. Bless you for your time. Visit us again soon.
Get Quote